HOG2 (TM) HOG Scrubber ® Hang On Glass Upflow Algae Scrubber ® with Green Grabber ® surfaces. For 1/4" (6mm) to 5/8" (16mm) acrylic or glass walls. Remove nuisance algae, nitrate and phosphate. From new to green in 3 cleanings, of the less powerful HOG1.3.
Unboxing and Shade Cloth Installatioin, of the more powerful HOG3. Unboxing and Installation Video, of the less powerful HOG1.3. Comparison of HOG2 to the HOG1.3 and HOG3. Get the no-overflow advantage of an upflow scrubber: since it is ALL underwater, it can't overflow onto your floor. This is the first larger Hang-On-Glass version of the standard HOG.
5, HOG1, and HOG1x algae scrubbers, which were the first HOG scrubbers available. This HOG2 offers much larger algae-attachment space to hold more growth between cleanings, and also stronger magnets to attach to thicker aquarium walls up to 5/8 (16mm) glass or acrylic. If your tank is larger than a nano, then you should consider this model or larger. This HOG2 Scrubber has 48 square inches (300 square cm) of one-sided algal growth surface, which once growing is designed to absorb the nutrients from this much feeding per day. 20 Pinches of flake, or.
20 Square inches (125 square cm) of nori, or. 5.6 grams of pellets. The number of gallons or liters of water in your tank or sump does not matter.
If you feed more than the above amounts you can get multiple HOG2 units; multiple units are preferred over one larger unit because you can clean one unit per week, and because you'll always have one unit filtering while the other one starts growing again after a cleaning. Multiple units are also good for backup. The magnets attach the outside cover to the inside cover through the aquarium wall, and can be used on glass or acrylic.1/4 inch (6 mm) to 5/8 inch (16 mm). If your aquarium wall is 3/4 (18mm) it might work but you won't know until you try; it would be better to put the HOG2 in your sump instead; it will work the same. Compared to the HOG1.3 and HOG3 which look the same in size, the HOG2 is meant for situations which have measurable nutrients in the water (nitrate between 5 and 20, or phosphate between 0.1 and 0.3) or some algae problems, but not too much. The large inside space of the growth compartment allows for lots of build up of algae over a long time, and the good power 4 LED light grows algae at good pace.
So this model is great for aquariums that have started to have problems but is not out of control yet. The light is strong enough however to require light-reduction to get started like the stronger HOG3, and comes with a cloth to cover the LEDs for the first week or two. Algal growth surface is so rough and prickly that it might be the roughest thing you've ever felt. A cactus might be sharper, but that's about it. Rough surfaces are critical for allowing algae to attach and grow and thus provide strong absorption of nutrients.
The rock-hard protrusions stick straight out 1 to 3 mm. Old style algae scrubber screens are made from "slippery" plastic canvas that is used for sewing and knitting; algae takes a long time to attach to it. Green-Grabber growth surfaces are not plastic at all; instead they are rock hard and have jagged rough edges and points (don't let children play with them). And the white color of the Green-Grabber surface reflects as much light as possible, getting almost the effectiveness of a 2-sided growth surface even though it really only has a light on one side of the surface.This is a hand-built Hang-On-Glass® (HOG) Upflow Algae Scrubber® (UAS) with a Green-Grabber growth surface, for glass or acrylic. This is the typical thickness range for most aquariums, and larger sumps, however you should measure yours to be sure.
If your tank uses thin 1/8 (3mm) glass such as many low-cost 10 gallon aquariums do, this filter is not recommended because the magnets are strong enough that they might crack the glass. You would be better off getting a lower cost HOG. No electrical parts go inside the aquarium; only air. And the air bubbler is already supplied (it's sealed behind the growth surface), so you don't have to get an airstone.The bubbler is simply vinyl air hose that has been cut lengthwise, and with cross-cuts, to form little flexible segments that are both adjustable and open-able to allow for easy cleaning. This HOG2 will run on. And comes with a 10 ft (300 cm) power cord with a U. If you require a different plug you can get an adapter at any local hardware or travel store, or online, or you can cut off the U. Plug and install your own plug from a hardware store. Comes with 3 ft (90 cm) of vinyl airline, but. That can pump at least 2.0 liters per minute. A pump that says it can handle 2 or more airstones/outlets, or a pump with 2 tubing attachments instead of one, will be needed. You can have as much air as you like, however; 10 lpm pumps are no problem (although it will be louder). One powerful pump which works exceptionally well for a low cost is the. Fusion 700 Air Pump from JW Pet. It is quiet and has two outputs which are adjustable by turning the control knob.
Another even more powerful and completely silent pump, although more expensive and without a control, is the Whisper AP 300 from Tetra. With either pump you will need to combine the two outputs into one to feed the scrubber, using something such as the "Tee" air line tubing fitting from Tom Aquatics (which we include with the Fusion 700).
Make sure to put the air pump above the aquarium so that it will not drain any water if it shuts off. One pump which works well is the Fusion 700 from JW Pet, which we sell here. Comes with 4 red (660 nm) 3-watt LEDs, which are attached to two heat sinks inside the cover. The LEDs will give the aquarium or sump a slight red color at night when the aquarium lights are off. Need to get a timer.
So you can run the LEDs for up to 22 hours per day (not 24). The LEDs never needs replacing. The HOG2 growth surface will need to be cleaned every 7 to 21 days, by removing the inside cover, disconnecting the airline, and taking the inside cover to the sink so you can brush the algae off of the growth surface and the bubbler with a toothbrush. No hard scraping is needed; just brush it with a toothbrush. The Green-Grabber growth surface is permanently glued to the inside cover using epoxy, however a few of the Green-Grabber particles may dislodge during the first few cleanings, which is normal.Cleaning the growth surface, bubbler, and the inside cover takes about a minute with a toothbrush. The HOG2 comes with a.
We specifically disclaim any and all implied warranties, including but not limited to lost profits, downtime, goodwill, damage to or replacement of other equipment and property, and any costs of recovering animals, plants, tanks or other aquarium related items and/or equipment. We cannot mark it as "gift". HOG2 size: Each cover is 6 5/8" wide x 8 3/4" high x 1 1/2 thick (16.6cm wide x 21.9cm high x 3.75cm thick).
It requires at least 7 (17.5cm) of water to operate in. The HOG2 is working fantastic; the test results are near perfect. Thanks for such a fantastic product -- Centralscot on the scrubber site.
You provided us with our very first [HOG2] public donation and have started us on our way. The scholars are excited about the ATS and cannot wait until we can get everything else. - William Romney, Assistant Pricipal, New Visions High School, Jamaica, New York, USA.
The item "HOG2 UAS upflow ATS scrubber with Green-Grabber Santa Monica Filtration" is in sale since Thursday, May 08, 2014. This item is in the category "Pet Supplies\Fish & Aquariums\Filters". The seller is "santa-monica-filtration" and is located in Santa Monica, California. This item can be shipped worldwide.