TRIGGER SYSTEMS EMERALD 39 SUMP - 40 GALLONS - 39"L x 16"W x 15T. Lighting - FIxtures & Bulbs. The Emerald series introduces several new features not found anywhere else.
Some of the features of the EMERALD39 are. Configurable input fitting plate (Patent Pending).
Laser etched lid to prevent splashing and reduce noise. Self adjusting foam block platform (Patent Pending). Laser engraved water level indicator. 0.25 hose holder for dosing and ATO inputs.Emerald green coloring to block light and prevent unwanted algae growth in other sections. The EMERALD39 has 4 main sections. Water enters the sump into a dedicated section where the water will then flow over into Section 1.
Section 1 is the configurable interchangeable plate area allowing for filter sock and/or foam block mechanical filtration. This area is covered with a lid to prevent water splashing and reduce noise. Water then flows out the bottom of Section 1 into Section 2. Section 2 is typically where the protein skimmer is located.Water then flows through the Trigger Symbol cutout into Section 3. Section 3 is the refugium section. The water then flows over the adjustable water level baffle through 2 perforated platforms and under the last baffle into Section 3. The top perforated platform comes with a foam block filter and the bottom one is open to use for several different filtration methods bag of carbon, bio balls, bio media, rubble rock, etc.
Section 4 is the return section where the return pump will sit, pumping water back to the display tank. Lid to prevent splashing and reduce noise. 0.25 hose inputs for dosing and ATO. Adjustable water level with self adjusting top platform.Full top support brace to prevent bowing. The EMERALD39 comes with the following accessories for Section 1. The Filter Sock Plate can be installed with filter socks as shown.
The EMERALD39 had three 4 socks, EMERALD34 model shown in images. The Foam Block Distribution Plate is perforated with holes and can be used when filter socks are not desired or in the case when the filter socks need to be changed or cleaned but replacement socks are not readily available and you want to maintain some level of mechanical filtration.
In this case, simply remove the filter socks and install the Foam Block Distribution Plate with the foam block. The Foam Block Distribution Plate may also be used on top of the Filter Sock Plate with filter socks. This configuration helps to distribute the water more evenly across all socks so that the filter socks will last longer before clogging and will clog at the same time. This also helps to silence the water noise by slowing down and spreading the water more evenly across the surface area of all of the socks. In this configuration, the foam block filter can be placed on top to enhance even further the silencing and distribution of water and also allow even longer times before the socks become clogged by providing a pre-filter before the socks.This configuration is shown in the image and is the default configuration. The EMERALD39 come with a probe holder that can hold up to three probes. The two outside holes are 0.63 in diameter and the center hole is 0.8 in diameter to fit different sized probes. ADJUSTABLE WATER LEVEL WITH SELF ADJUSTING FOAM BLOCK. Water level in the sump is adjustable from 7 to 9.5 to accommodate for the water height requirements for different protein skimmers.
Simply move the baffle to the desired height location and tighten the two bolts to hold in place. As the water level is adjusted by sliding the wall up and down, the foam block filter and the top perforated platform also move up and down automatically.
This is important to maintain the correct location of the foam block sponge filter with respect to the sump water height and also to maximize the media capacity for the bottom platform. LASER ENGRAVED WATER LEVEL INDICATOR. Subtle water level height indicator is laser engraved on the inside wall to help when setting the adjustable water level to to the desired water height based on protein skimmer requirements. All Emerald sumps also come with 4 holes in the top support brace for holding in place 1/4 OD tubing from reactors, dosing containers or ATOs. The laser etched lid over the interchangeable plate section allows for easy access to the filter socks and foam filter while providing suppressed noise and splashing.
Dimensions: 39 long x 16 wide x 15 high Skimmer Section: 14 x 15.5 Center/Refugium Section: 10.5 x 15.5 Return Pump Section: 6 x 15.5 Total Water Volume: 40 gallons Skimmer Water Level: 7 to 9.5 adjustable Drain Input Fittings: 1 (both x2 and x3) Filter Socks: 4 (x3). Our primary warehouses are in PA, CA, SC, FL and AZ.Tracking information is provided with every order. Customers must allow an extra week of processing time for some items. Airfreight is the cheaper option but it's all up to you the customer. At The Coral Life we strive to do things different than the other outlets. We aim to keep things simple and only sell products we currently own or have used in the past. This is more than a business it is a passion. There's thousands of online stores, some who are cheaper, who simply try to sell anything and everything under the sun, with no care in the world of quality in the product or service. This does a few things for us. We know the products inside and out because, we use them in our reefs/tanks. We should be able to answer any question you have for us on a product. Setting up our store in this manner makes for a better overall experience for our customers. So if ever have a complaint please reach out to us before leaving feedback - as most can tell when they get a special treat with there packages ;- our service is customer minded. The item "TRIGGER SYSTEMS EMERALD 39 SUMP 40 GALLONS 39L x 16W x 15T" is in sale since Friday, April 7, 2017. This item is in the category "Pet Supplies\Fish & Aquariums\Filters". The seller is "thecorallife" and is located in Columbia, South Carolina.
This item can be shipped to United States, Canada, Mexico, Bermuda.